K6-C1
K6-C1_22K6-C Multifunctional coating thickness gaugePH3-1.8 Eddy current phase measurement method probeNickel on steel thickness measurement with PH3-1.8 probe

Product Description

K6-C Multifunctional Coating Thickness Gauge

Purpose
K6-C Multifunctional coating thickness gaugeThickness measurement of:
— galvanic (zinc, chromium, nickel, cadmium, silver, tin and other) coatings on steel products;
— galvanic (zinc, chromium, nickel, cadmium, silver, tin and other) coatings on products from non-ferrous metals;
— paint, lacquer, enamel, powder, mastic and other dielectric coatings on steel products;
— anodic oxide, phosphate and other dielectric coatings on ferrous and non-ferrous metals;
— special dielectric and metallic thick coatings, plated coatings;
— coatings on the internal surfaces of pipes and cylindrical products;
— copper foils on printed circuit boards;
— sheets of conductive non-ferrous materials and galvanic coatings on products from dielectric materials;
— two layers coatings;
— protective layer of concrete and determination of steel reinforcement position in concrete;
— wall thickness of large products from fiberglass and carbon fiber reinforced plastics during manufacture and delivery with one side and two sides access;
Measurement of groove depth and evaluation of surface roughness after sand blasting or grit blasting;
Control of climatic conditions (air humidity, air and metal surface temperature, dew point temperature and determination of TΔ parameter).

Features
— TFT colour display with 2.4” diagonal and a built-in Li-Ion battery;
— shockproof ergonomic body with rubberized corners;
— keyboard with functional keys that change their purpose depending on the mode of operation of the device and user-friendly and intuitive interface;
— additional modes and device settings;
— extended set of wear-resistant ergonomic small-sized transducers;
— support for transducers with several calibration characteristics (up to 6 for PH3 series probes, up to 4 for NF-G probes, up to 2 F-G probes).

Basic technical characteristics
the range of thickness control: 0.5 µm…120 mm (depends on connected transducer);
number of transducers: unlimited (according to customer’s choice);
temperature range:for device: -10…+40 °C (-30 ° C for frost-resistant version), for transducers: -40…+50 °C (up to +350 °C for high temperature transducers);
calibration methods: additive one-point, two-point, one-point with automatic multiplicative correction;
power supply: built-in Li-Ion battery in 3.7-4.2 V, 1500-1700 mAh;
continuous operation time: min. 12 hours;
connectivity with PC: USB 2.0 channel;
overall dimensions: 60 × 125 × 25 mm;
weight of electronic unit: 120 g;
charging time: 4 h.

Delivery set
Measuring unit with transducers (number and modification depend on customer’s choice), charging unit, set of coating thickness reference specimens and basis reference specimens (based on selected transducers), mini-USB — USB A Type cable for connection with computer, operating manual, shockproof case.

 


 Combined Magneto-Inductive and Eddy Current Parametric Measurement Method Probe

FNF
Probe for thickness measurement of paint, powder, plastic, enamel and other non-ferrous dielectric
coatings on conductive ferrous and non-ferrous materials.

FNF

Technical features

  • measurement range, T: 0-1000 μm (1 mm);
  • measurement accuracy, μm: ± (0,015T+1);
  • diameter of test area, mm: 6;
  • minimum diameter of substrate, mm, Øconvex/Øconcave: 4/12;
  • dimensions, mm: Ø21×90.

Probes for the Magneto-Inductive measurement method

Probes F for K6-C contain one calibration characteristics for coatings thickness measurement on ferromagnetic bases.

F0 
Probe for galvanic (zinc, chrome, cadmium, etc.) and dielectric (plastic, paint, etc.) coatings on small-sized parts (with small radius of curvature) and in hard-to-reach areas made of ferromagnetic materials.

 

F0_1
Technical features

  • measurement range, T: 0-300 µm (0,3mm);
  • measurement accuracy, ±(0,02T+1) µm
  • diameter of test area, Øm, mm: 3 ;
  • minimum diameter of substrate, mm, Øconc ( Øconv): 4,5 (1).
  • dimensions, mm: Ø9×115

Particulars
Probe of pencil type with fixed measurement system. Minimum diameter of test area provides complete tuning out from influence of coating electric conductivity.


F0/90
Probe for galvanic (zinc, chrome, cadmium, etc.) and dielectric (plastic, paint, etc.) coatings on small-sized parts (with small radius of curvature) and in hard-to-reach areas made of ferromagnetic materials.

F0_90 (right angle probe)

Technical features

  • measurement range, T: 0-300 µm (0,3mm);
  • measurement accuracy, ±(0,02T+1) µm
  • diameter of test area, Øm, mm: 3 ;
  • minimum diameter of substrate, mm, Øconc ( Øconv): 4,5 (1).
  • dimensions, mm: Ø20×127

F1
Probe for measuring of galvanic (zinc, chrome, cadmium, etc.) and dielectric (plastic, paint, etc.) coatings upon small-size articles made of ferromagnetic materials.

F1_1
Technical features

  • measurement range, T: 0-500 µm (0,5mm);
  • measurement accuracy: ±(0,02T+1) µm;
  • diameter of test area, Øm, mm: 4 ;
  • minimum diameter of substrate, mm, Øconc ( Øconv): 4,5 (1);
  • dimensions, mm: Ø9×65.

Particulars
Wear-resistant probe with spring-loaded measuring system for control of galvanic coatings, provides complete tuning out from influence of coating ’ s electric conductivity.


F2
Probe for dielectric (paint, powder, anode oxide, etc.) and current-conducting non-ferromagnetic (zinc, chrome, etc.) coatings upon articles made of ferromagnetic materials within the range of up to 2 mm.

F2
Technical features

  • measurement range, T: 0-2000 µm (2mm);
  • measurement accuracy: ±0,02T µm;
  • diameter of test area, Øm, mm: 6 ;
  • minimum diameter of substrate, mm, Øconc ( Øconv): 9,0 (1,5);
  • dimensions, mm: Ø19×83.

Particulars
probe with  spring-loaded measuring system. Use of hard-metal material for the tip allows to exclude its wear-out.


F3
Probe for dielectric (paint, powder, anode oxide, etc.) and current-conducting non-ferromagnetic (zinc, chrome, etc.) coatings upon articles made of ferromagnetic materials within the range of up to 5 mm.

F3
Technical features

  • measurement range, T: 0-5000 µm (5mm);
  • measurement accuracy: ±0,02T µm;
  • diameter of test area, Øm, mm: 8 ;
  • minimum diameter of substrate, mm, Øconc ( Øconv): 10,5 (2,5);
  • dimensions, mm: Ø19×83.

Particulars
probe with  spring-loaded measuring system for thick coatings.


F4
Thickness measurement of bitumen, plastic, foil, heat resistant and other non-ferrous coatings (including special purpose coatings) on substrates from steel with average and large surface roughness.

F4

Technical features

  • measurement range, T: 0-8000 µm (0-8 mm);
  • accuracy in measurement range: 0–6 mm: ≤±(0,015T +0,01) mm; 6–8 mm: ≤±0,02T;
  • minimum diameter of substrate, outer diameter/inner diameter, mm : 5/18,5;
  • diameter of test area Øm, mm: 12;
  • dimensions, mm: Ø15×49.

F5
Thickness measurement of bitumen, plastic, foil, heat resistant and other non-ferrous coatings (including special purpose coatings) on substrates from steel with average and large surface roughness.

F5

Technical features

  • measurement range, T: 0-1000 µm (0-10 mm);
  • accuracy in measurement range: 0-10 mm 1–8 mm: ≤±(0,015T+0,01) mm; 8–10 mm: ≤±0,02T;
  • minimum diameter of substrate, outer diameter/inner diameter, mm : 7/57;
  • diameter of test area Øm, mm: 17;
  • dimensions, mm:  Ø23×58.

 


Probes for the Eddy-Current measurement method

Probes NF for K6-C contain one calibration characteristics for coatings thickness measurement on non-ferromagnetic bases.

NF0
Probe for measuring of dielectric (paint, anode oxide, powder, etc) and current-conducting non-ferromagnetic (tin, zinc, etc.) coatings upon articles made of current-conducting non-ferromagnetic materials within the range of up to 500  µm.

NF0
Technical features:

  • measurement range, T: 0-500 µm (0,5mm);
  • measurement accuracy: ±(0,02T+1) µm;
  • diameter of test area, mm: 1,5 ;
  • size, mm: Ø6×35.

Particulars
Probes with  spring-loaded measuring system. Utilization of modern durable materials  provides high strength and wear resistance of probe.


NF1
F2
Probe for measuring of thickness of dielectric (paint, anode oxide, powder, etc) and current-conducting non-ferromagnetic (tin, zinc, etc.) coatings upon articles made of current-conducting non-ferromagnetic materials within the range of up to 2000  µm,
Technical features

  • measurement range, T: 0-2000 µm (2mm);
  • measurement accuracy: ±0,02T µm;
  • diameter of test area, mm: 4,7 ;
  • size, mm: Ø6×35.

Particulars
Probes with  spring-loaded measuring system. Utilization of modern materials  provides high strength and wear resistance of probe.


NF2 – NF4

Probe for measuring of thick dielectric coating (up to 60 mm) on metal substrates
Technical features
NF2

F2

 

  • measurement range, T: 0-15000 µm (15mm);
  • measurement accuracy: ±0,02T µm;
  • diameter of test area, mm: 20 ;
  • minimum radius of base, mm, Øconc ( Øconv): 12 (5);
  • size, mm: Ø15×85.

NF3

F2

  • measurement range, T: 0-30000 µm (30mm);
  • measurement accuracy: ±0,02T µm;
  • diameter of test area, mm: 40 ;
  • minimum radius of base, mm, Øconc ( Øconv): 45 (15);
  • size, mm: Ø23×88.

NF4

NF4 (2)

  • measurement range, T, mm: 0-70;
  • measurement accuracy,  mm, 0-40 mm: ≤( 1% ± 0,1); 40-70 mm: 2%;
  • diameter of test area, mm: 90;
  • minimum radius of base, mm, Øconc ( Øconv): 270 (80);
  • size, mm: Ø80×60.

Particulars
probes with  spring-loaded measuring system. High temperature and stability of indications during work in field conditions.


Probes for the Eddy-Current phase measurement method

Probes PH for K6-C contain one “coating/base” characteristics.

PH1
Probe for measuring of the electrolytic nickel and other galvanic coatings upon steel substrates.

PH1 (2)
Technical features:

  • measurement range, T, µm: 0-120;
  • measurement accuracy,  µm: ≤±( 0,03T + 1);
  • minimum radius of base, mm : 1;
  • diameter of test area, mm: 4,7 ;
  • size, mm: Ø12×40.

Particulars
Possibility of control of galvanic coatings under dielectric layers.


PH3
Probe for measuring of galvanic coatings.

 

PH3 (2)
PH3-1.8 Eddy current phase method probe

Technical features: PH3-0,2 || PH3-1,8

  • measurement range, T, µm: 0-120 || 40;
  • measurement accuracy,  µm: ≤±( 0,03T + 1) || ≤±( 0,03T + 1 );
  • minimum radius of base, mm : 1 || 75;
  • diameter of test area, mm: 1 || 1 ;
  • size, mm: Ø6×50 || Ø6×50.

Particulars
Possibility of control of galvanic coatings under dielectric layers.

 


Specialized probes

FxP, NFxP
Probe for measuring inside pipes made of ferromagnetic (FxP) and non-ferromagnetic (NFxP) materials.

NFxP
Technical features

  • measurement range, T, µm: 0-2;
  • measurement accuracy,  µm: ≤±( 0,02T+ 0,001);
  • minimum diameter of pipe, mm: 14;
  • diameter of test area, mm: 4,7.

Particulars
Design of probes allows control in manual mode the pipes opened from two sides. Appliances for pilling probe depends on diameter and length of pipe.


FR1
Probe for measuring of thickness of concrete down to rebar and determination of rebar location.

FR1
Technical features

  • measurement range, T, for concrete, mm: 70;
  • measurement accuracy,  mm: ≤±( 0,05T + 0,1);
  • diameter of rebar, mm: 3-40;
  • size, mm: 100x30x50.

Particulars
Possibility of operation in wide range of thickness of concrete and diameters of rebar.


FR2
Probe for measuring the thick protective coatings (up to 120 mm) on ferromagnetic surfaces.

FR1
Technical features:

  • measurement range, T, mm: 1-120;
  • measurement accuracy,  mm: ≤±( 0,05T + 0,1);
  • size, mm: 180x30x50.

R
Probe for roughness measurement after the sand and grit blasting prior to painting works.

NFxP
Technical features

  • roughness measurement range, µ m: 3-300;
  • measurement accuracy,  Rz: ≤± 0,02;
  • size, mm: Ø12×45.

THDC

Probe for measurement of metal surface temperature, air temperature, relative air humidity, temperature of dew point and calculation of the difference between metal surface temperature and temperature of dew point (inspection of conditions during painting of metal products).

THDC probe with device

Temperature_Humidity_Dew Point Temperature_Surface Contact Temperature THDC probe

Data shown on device display
when THDC probe is connected

 

THD THD_2
Probe for measuring of air temperature, humidity and dew point during execution of paint works.
Technical features
1) measurement range:

  • air temperature: -10°C – +40°C;
  • humidity: 5-90%;
  • dew point, °C: -15° – 40°.

2) measurement accuracy:

  • humidity, °C : ≤± 5%;
  • air temperature, °C: ±1 ° ;
  • dew point, °C: ≤± 2 °.

3) size, mm: Ø15×120.
Particulars
probe of integral type with  wide limits of measuring.

Reviews

There are no reviews yet.

Be the first to review “K6-C”